SUMMIT FG 100

Fully synthetic compressor oils for the food-processing and pharmaceutical industries.

Klüber Summit FG oils are special compressor oils developed for the food-processing and pharmaceutical industries. They are fully synthetic and can be mixed with mineral oil as well as other synthetic hydrocarbon oils.

Klüber Summit FG oils offer very good oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators.

Klüber Summit FG oils are NSF H1 registered and therefore comply with FDA 21 CFR § 178.3570. The lubricants were developed for incidental contact with products and packaging materials in the food-processing, cosmetics, pharmaceutical or animal feed industries. The use of Klüber Summit FG oils can contribute to increase reliability of your production processes. We nevertheless recommend conducting an additional risk analysis, e.g. HACCP.

Klüber Summit FG oils can be used as vacuum pump oils, evacuating air or inert gases if a food grade oil is required. Klüber Summit FG oils can be used for oil-injected screw-type compressors, reciprocating piston compressors and rotary vane compressors.
Klüber Summit FG oils are intended for use in compressors of the food-processing and pharmaceutical industries requiring oil-free compressed air (without oil vapour, which cannot be removed by the oil separator).
These oils are also suitable for gear lubrication in oil-free screw-type compressors.
When selecting the oil viscosity for air compressors, please observe the manufacturers' instructions.
For oil-injected screw-type compressors normally the viscosity grades ISO VG 32, 46 and 68 are used, for reciprocating piston and rotary vane compressors ISO VG 68, 100 and 150 and for centrifugal compressors ISO VG 32.
Notes on switching from mineral to synthetic oils: When switching a used compressor to a Klüber Summit FG oil, drain old oil from whole circuit of compressor while still warm.
We also recommend changing all oil filters and separators. Then refill the compressor with Klüber Summit FG oil.
When switching from mineral oil to a synthetic Klüber Summit FG oil please bear in mind that the compressor may contain oxidation residues in the form of blackened or contaminated oil.
As such residues can affect the service life of the fresh Klüber Summit FG oil, the compressor should be cleaned using the Klüber Summit Varnasolv conditioner.
After switching to a Klüber Summit FG oil we recommend determining the oil change interval through an oil analysis after approx. 500 to 1000 operating hours

Klüber Summit FG oils are NSF H1 registered for use in the food-processing and pharmaceutical industries and comply with FDA 21 CFR Sec 178.3570
ISO 21469 certified – supports compliance with the hygienic requirements of your production.
Low maintenance and operating costs due to extended oil change intervals up to 5,000 operating hours in oil-injected screw-type compressors *
Easy compressor conversion from mineral to the synthetic Klüber Summit FG oils due to miscibility and compatibility with common seal materials **
Low tendency to evaporation and thus low impact of the oil vapour on the compressed air
Longer service of oils filters, activated carbon filters and oil separators
Excellent demulsifying behaviour and hence good water separation ability
Surpasses the requirements of DIN 51506-VDL and ISO 6743-3 L-DAJ (VG 32/46/68) / L-DAB (VG 100/150)

Ürün Bilgisi	Klüber Summit FG 100	Klüber Summit FG 200	Klüber Summit FG 250	Klüber Summit FG 300
Artikel Numarası	050008	050009	050095	050010
NSF-H1, K3 Tescil Numarası	143606	143607	143609	143610
Sudan Ayrılma Kapasitesi, DIN ISO 6614 /ASTM D1401, 54°C	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)	-
Sudan Ayrılma Kapasitesi, DIN ISO 6614 /ASTM D1401, 82°C	-	-	-	40-37-3 (60) ml (min)
Yoğunluk, DIN 51757, 20°C	Yaklaşık 0.83 g/cm³	Yaklaşık 0.83 g/cm³	Yaklaşık 0.84 g/cm³	Yaklaşık 0.84 g/cm³
Parlama Noktası, DIN EN ISO 2592, Cleveland, Açık Kap	≥ 230 °C	≥ 240 °C	≥ 250 °C	≥ 250 °C
Kinematik Viskozite, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C	Yaklaşık 5.8 mm²/s	Yaklaşık 7.5 mm²/s	Yaklaşık 10.4 mm²/s	Yaklaşık 13 mm²/s
Kinematik Viskozite, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C	Yaklaşık 32 mm²/s	Yaklaşık 46 mm²/s	Yaklaşık 68 mm²/s	Yaklaşık 100 mm²/s
Viskozite İndeksi, DIN ISO 2909	≥ 120	≥ 120	≥ 120	≥ 120
Akma Noktası, DIN ISO 3016	≤ -50 °C	≤ -50 °C	≤ -50 °C	≤ -45 °C
Üretim Tarihinden İtibaren Minimum Raf Ömrü – Açılmamış Orijinal Ambalajında, Serin ve Kuru Yerde, Yaklaşık	60 Ay	60 Ay	60 Ay	60 Ay

Ürün Bilgisi	Klüber Summit FG 100
Artikel Numarası	050096
NSF-H1, K3 Tescil Numarası	143608
Sudan Ayrılma Kapasitesi, DIN ISO 6614 /ASTM D1401, 54°C	-
Sudan Ayrılma Kapasitesi, DIN ISO 6614 /ASTM D1401, 82°C	40-37-3 (60) ml (min)
Yoğunluk, DIN 51757, 20°C	Yaklaşık 0.84 g/cm³
Parlama Noktası, DIN EN ISO 2592, Cleveland, Açık Kap	≥ 250 °C
Kinematik Viskozite, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C	Yaklaşık 19 mm²/s
Kinematik Viskozite, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C	Yaklaşık 150 mm²/s
Viskozite İndeksi, DIN ISO 2909	≥ 120
Akma Noktası, DIN ISO 3016	≤ -39 °C
Üretim Tarihinden İtibaren Minimum Raf Ömrü – Açılmamış Orijinal Ambalajında, Serin ve Kuru Yerde, Yaklaşık	60 Ay

kluber-summit-fg-100.pdf kluber-summit-fg-100-en.pdf

Products

Home-Page | Products | SUMMIT FG 100

SUMMIT FG 100