SUMMIT PS

Semi-synthetic air compressor oils for oil change intervals up to 5,000 operating hours.

Klüber Summit PS oils are air compressor oils based on hydrogenated mineral oil, synthetic ester oil and additives. Klüber Summit PS oils are miscible with mineral oils and synthetic hydrocarbons, but not with oils based on polyglycol.

Klüber Summit PS oils are specially formulated for screw and piston compressors. They are used to increase oil change intervals in screw compressors up to 5,000 operating hours.
Klüber Summit PS oils can be used in compressors that have previously operated with ordinary mineral oils. These oils are neutral to many elastomers and seals in air compressors; In this way, leakage is not expected to occur.
Klüber Summit PS oils are preferred in cases where the desired oil change intervals cannot be achieved when using mineral oil and where fully synthetic oils are expensive and are not economical due to lower annual operating hours.
Klüber Summit PS 100 is used specifically for turbo compressors, while Klüber Summit PS 300 and 400 are specially formulated for reciprocating compressors.
Klüber Summit PS oils offer good oxidation stability with their synthetic-based content, thus minimizing oxidation residue in the compressor and extending the operating life of filters and separators by extending oil change intervals. Special inhibitors contained in the oil keep the inside of the compressors clean and provide high efficiency.

Low maintenance and operating costs due to oil change intervals up to 5,000 operating hours inoil-injected screw-type compressors
Easier compressor oil changeover due to neutral behaviour of oils towards seals
Good soil dissolving capacity, clean oil circuit due to the ester content in the oil, reduction of cleaning costs
Low formation of oxidation residues in the oil circuit, reduced operating costs due to extended oil filter and separator life
Complies with the requirements of DIN 51506-VDL and ISO 6743-3 L-DAJ (VG 32/46/68) / L-DAB (VG 100/150)

Characteristics	Klüber Summit PS 100	Klüber Summit PS 150	Klüber Summit PS 200	Klüber Summit PS 300	Klüber Summit PS 400
Article number	050052	050053	050054	050055	050056
Appearance	clear	clear	clear	clear	clear
Colour space	colourless	colourless	colourless	colourless	colourless
Demulsifying capacity, DIN ISO 6614 /ASTM D1401, 54°C	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)	-
Demulsifying capacity, DIN ISO 6614 /ASTM D1401, 82°C	-	-	-	40-37-3 (60) ml (min)	40-37-3 (60) ml (min)
Density, DIN 51757, 20°C	approx. 0.87 g/cm³	approx. 0.87 g/cm³	approx. 0.87 g/cm³	approx. 0.88 g/cm³	approx. 0.88 g/cm³
Flash point, DIN EN ISO 2592, Cleveland open cup	≥ 200 °C	≥ 210 °C	≥ 230 °C	≥ 240 °C	≥ 240 °C
Foam test, ISO 6247 / ASTM D892, 24°C, sequence I	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml
Foam test, ISO 6247 / ASTM D892, 24°C, sequence III	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml
Foam test, ISO 6247 / ASTM D892, 93.5°C, sequence II	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml	≤ 50/0 ml
ISO viscosity grade, DIN ISO 3448, ISO VG	32	46	68	100	150
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C	approx. 5.5 mm²/s	approx. 6.8 mm²/s	approx. 8.4 mm²/s	approx. 10.6 mm²/s	approx. 14.3 mm²/s
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C	approx. 32 mm²/s	approx. 46 mm²/s	approx. 68 mm²/s	approx. 100 mm²/s	approx. 150 mm²/s
Viscosity index, DIN ISO 2909	≥ 90	≥ 90	≥ 90	≥ 90	≥ 90
Copper corrosion, DIN EN ISO 2160, 3 h, 100°C 1	1 - 100 - 3 corrosion degree	1 - 100 - 3 corrosion degree	1 - 100 - 3 corrosion degree	1 - 100 - 3 corrosion degree	1 - 100 - 3 corrosion degree
Pour point, DIN ISO 3016	≤ -30 °C	≤ -30 °C	≤ -27 °C	≤ -30 °C	≤ -27 °C
Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx.	36 months	36 months		36 months	36 months

kluber-summit-ps.pdf kluber-summit-ps-en.pdf

Products

Home-Page | Products | SUMMIT PS

SUMMIT PS